Introduction | Geotechnical Documents and Software | Marine Documents | Other Downloads | Contact Us

Visit Our Online Bookstore

New on vulcanhammer.net:

Five New Geotechnical Documents 17 April 2008 17:24
Behind every great patent is... 02 March 2008 11:30
New Marine and Geotechnical Documents 20 February 2008 00:35
New Books, CD's and Documents 09 January 2008 17:54
A Site Update, and a New Document 20 December 2007 11:24
vulcanhammer.net Marine and Airport CD Library Now Available 04 December 2007 09:50

Geotechnical Documents and Software

Material on Related Sites

Special Geotechnical Features

CLM2 (Characteristic Load Method)

Spreadsheet for Microsoft Excel; documentation included with spreadsheet.

 The characteristic load method (CLM) of analysis of laterally loaded piles (Duncan et al., 1994) was developed by performing nonlinear p-y analyses for a wide range of free-head and fixed-head piles and drilled shafts in clay and sand. The results of the analyses were used to develop nonlinear relationships between dimensionless measures of load and deflection. These relationships were found to be capable of representing the nonlinear behavior of single piles and drilled shafts quite accurately, producing essentially the same values of deflection and maximum moment as p-y analysis computer programs like COM624 and LpilePlus3. The principal limitation of the CLM method is that it is applicable only to uniform soil conditions. The Group Amplification Method was developed by Ooi and Duncan (1994), to extend use of the CLM method to groups of piles and drilled shafts. Values of group amplification factors for deflection and moment were computed using the method developed by Focht and Koch (1973).

The original version of the CLM spreadsheet (Brettmann and Duncan, 1996) used the CLM method to calculate deflections and bending moments in single piles, and the Group Amplification Method to calculate deflections and moments for piles in pile groups. It was found that the original version of the spreadsheet resulted in accurate values of moment and deflection for single piles, but often over-estimated deflections and bending moments for the piles in pile groups, as judged by comparison with p-y analysis programs and the results of field load tests.

The revised spreadsheet uses p-y multipliers as the basis for improving the accuracy of pile group analyses. The p-y multiplier values used are those recommended by Mokwa and Duncan(2001) based on their field tests and review of recent literature.

COM624P

Click here for program documentation (pdf format)

Note: a helper for this program is available at this site.
 A program for the analysis of the deflection and capacity of piles under lateral loads. It was developed by Lymon C. Reese and his colleagues at the University of Texas at Austin, and is based on the p-y curve method. The program solves the equations giving pile deflection, rotation, bending moment, and shear by using an iterative process due to the non-linear response of the soil.

COM624P is a DOS program which is installed from a self extracting file. Complete instructions and documentation is also available here as well.

DRIVEN

Click here for program documentation (pdf format)

 DRIVEN is a Microsoft Windows 95/98/Me/XP program, developed by the FHWA, to analyse the axial capacity of driven piles. Thurman (1964), Meyerhof (1976), Cheney and Chassie (1982), Tomlinson (1980, 1985), and Hannigan, et.al. (1997). The Nordlund and Tomlinson static analyses methods used by the program are semi-empirical methods and have limitations in terms of correlations with field measurements and pile variables which can be analysed. The user is encouraged to review further information on this subject in the "Design and Construction of Driven Pile Foundations" manual (Hannigan, et.al. 1997).

DRIVEN is downloaded and installed as follows:

  1. Download the driven.zip file into a temporary directory.
  2. Open the file with an appropriate file and extract the installation file into a temporary directory.
  3. Run the installation file, following the instructions.
  4. If you need it, download the instruction manual by clicking its hyperlink below.

LLP99 (Laterally Loaded Pile)

 This is a program for the analysis of a laterally loaded pile. It calculates the lateral displacements of the pile for a lateral load and a moment applied at the head of the pile. Input consists of the properties of the soil layers along the pile shaft, and the force and moment applied at the top of the pile, in a number of loading steps. Output is given on the screen, in the form of the response of the top of the pile. Input and output data can be printed, and are written to the datafile of the problem when it is saved after the analysis. These data can be inspected using a text editor. Documentation is in the program help.

The program must be extracted from a ZIP file before use. It is written for Microsoft Windows 95/98/Me/NT/2000/XP operating systems, and comes courtesy of Dr. Arnold Verruijt.

MICROWAVE (TTI Wave Equation Program)

 This program has its own dedicated page.

Click here for more information and access to download.

SPILE

A program for estimating the vertical load capacity of driven piles for both cohesionless (using Nordlund's method) and cohesive ones (using Tomlinson's Method.) The program is interactive and designed to analyse multilayered soils. It is primarily intended for small (less than 36") piles, such as H-beams, concrete and pipe piles.

Click here for more information and access to download.

WEAP87

The DOS wave equation program. This program has its own dedicated page.

Click here for more information and access to download.
Shared Bottom Border
 
Web www.vulcanhammer.net
www.vulcanhammer.info www.chet-aero.com
This entire site Copyright© 1997-2008 Don C. Warrington. All rights reserved.

Website maintained by Positive Infinity and hosted by 1 and 1 Internet.